12 VOLT Generator For 66cc 80cc 2 Stroke Engine Motorized Bicycle

12 VOLT Generator For 66cc 80cc 2 Stroke Engine Motorized Bicycle
12 VOLT Generator For 66cc 80cc 2 Stroke Engine Motorized Bicycle

12 VOLT Generator For 66cc 80cc 2 Stroke Engine Motorized Bicycle
12 Volt Mini-Generator ONLY For 2-Stroke Engines. Engine and Bicycle NOT included. Now you can get a reliable lighting system for your 2 cycle motorized bicycle by using this Mini-Generator Max designed for 12 volt lighting systems. This particular Mini-Gen is designed especially for pull start 2 cycle motorized bike engines. Like our regular 12 volt Mini-Gen, this will provide a self sufficient and dependable lighting system. The Mini-Generator is a small electrical unit designed to be mounted inside the engine's magneto case to produce electricity to the Mini-Charger which charges the batteries, or it can be used to produce lighting (up to 10 watts recommended) directly. This "Mini-Gen " is designed to produce AC voltage of 12 or more (nominal) for 12 volt/10 watt halogen headlights. Just install into magneto case using the 2 rear magneto screws and route red (output) wire through wire harness. The red wire from the Mini Generator will send electricity to your lights through a light switch or connected directly for continuous light. This Pull Start Mini-Gen is easily installed and includes installation instructions and precautions. Just remove the engine magneto cover, then remove the pull starter cog and use the 2 rear screws to attach Mini-Generator inside engine magneto case. Remove wire grommet at the front (white plastic or black rubber) then insert Mini-Gen wire into grommet. Use a pick or small screwdriver or nail to push into the area where wire will fit, then insert wire. This will produce over 12 volts AC at about 1300 RPM or driving speeds of about 12 to 15 MPH. If running lights directly from Mini-Gen Max, avoid revving engine with lights on to avoid blowing out lights.

High speeds while driving is O. Just temporarily install nut and turn the pull starter cog to make sure there is no rubbing on the Mini-Gen. Instructions and precautions are included for Mini-Gen installation.

After the Mini-Generator is installed, the power wire should be routed toward bicycle seat post for Mini-Charger connection, unless it's being used for other purpose. Wire inside engine case should be positioned away from moving parts and also make sure it will not be pinched under the cover. Use duct tape (any color) or cable ties to secure wire onto bike's bottom bracket and seat post. The Mini-Gen in this photo is connected to the red wire coming from the Mini-Charger. Your results will look far better than this one.

NOTE: For pull starter 2 cycle engines, run engine for about 10 seconds then remove cover and check to make sure there's no sign of pull starter cog rubbing on Mini-Gen. Here is the Mini-Gen-Max voltage being measured at approx. 1300 rpm's (normal driving speed = 1100 tp 1800 RPM). The magneto in this photo looks stationary because camera flash was used, but it's actually spinning.

# This is called a generator (which technically produces dc voltage), but this produces AC voltage. The engine speed here is around 1300 to 1350 RPM which is just around driving speed. Most riders will produce this voltage at a speed of around 15 to 18 MPH. Higher voltages of around 18 or more is obtainable at much higher engine speeds, but 12 volts is specified as the average voltage. The Mini-Gen is seen here hooked up to a common 12 volt 10 watts halogen headlight.

This type of lighting draws around 860 milliamps on a fully charged 12 volt battery and uses less ac amps due to the nature of ac current. Here in the photo you see the light using a little over 700 milliamps at around 1300 rpm. Unlike most LED lights, regular light bulbs will run off both AC and DC voltage with no problem. A complete 14.4 Volts Lighting System Will be available in our store very soon if not already available. Caution: Avoid revving up the engine if running lights directly from Mini-Gen Max because high revs of 3000 rpm for more than 5 seconds can immediately blow the bulbs. Feedback is very important to us. It is impossible to address issues if we do not know about them! For helping with your order or if you have any questions regarding our products. All messages are answered within 24-48 hours. We will do our best to resolve the issue. Thank you for looking, if you have any questions feel free to ask and we will do our best to get back to you promptly! For ALL Motorized Bicycles we can provide engines, engine kits, high performance spare parts, motorized bicycle and spare parts of bike.

The item "12 VOLT Generator For 66cc 80cc 2 Stroke Engine Motorized Bicycle" is in sale since Monday, November 19, 2018. This item is in the category "eBay Motors\Parts & Accessories\Motorcycle Parts\Other Motorcycle Parts".

The seller is "cafemotoracer" and is located in Las Vegas, Nevada. This item can be shipped worldwide.
12 VOLT Generator For 66cc 80cc 2 Stroke Engine Motorized Bicycle